RoboFocus

15 Item(s)
Set Descending Direction
  1. RoboFocus - Additional Motor Kit

    $140.00
    SKU: ROB-RFAM1

    Ships in 3-5 Days

    You can elect to use your RoboFocus system on a second telescope by purchasing and installing an additional motor. The Additional Motor Kit comes with a stepper motor and mounting hardware, (brackets, shaft coupler, and/or timing sprockets and belts).

    You must specify telescope/focuser that the system will be installed on. In some cases we may need to contact you for further information

  2. RoboFocus - AP Bracket

    $35.00
    SKU: ROB-RFB1

    Ships in 3-5 Days

    Custom bracket for Astro Physics focusers. This bracket is designed for both the 2 and 4 inch focusers. It is made with 0.125 aluminum with an attractive black power coat finish. The bracket is very stable and designed for fast and easy RoboFocus motor mounting.

  3. RoboFocus - Full RF3 System

    $495.00
    SKU: ROB-RF3M

    Ships in 3-5 Days

    The Mandel Adapter allows the attachment of a 35mm or digital SLR camera directly to the telescope focuser providing a "wide angle" imaging option.

    FREE SHIPPING(48 States)
  4. RoboFocus - Hand Paddle

    $30.00
    SKU: RFHP

    Ships in 3-5 Days

    The RF3 Hand Paddle allows manual focusing via a small hand controller on a 12 foot cable. The "in/out" buttons move the stepper motor to achieve visual focus. These buttons are duplicates of the ones on the RoboFocus controller box.

  5. RoboFocus - JMI DX1/DX2 Bracket

    $35.00
    SKU: ROB-RFB4

    Ships in 3-5 Days

    Custom bracket for JMI DX1 and DX2 focusers. Bracket is made with 0.125 aluminum with an attractive black powder coat finish. The bracket is very stable and designed for fast and easy RoboFocus motor mounting.

    Note: Two holes must be drilled in the focuser housing base. TI will drill and mount bracket at no charge if desired.

  6. RoboFocus - LX200 8 GPS Bracket

    $35.00
    SKU: ROB-RFB5

    Ships in 3-5 Days

    Custom bracket for the LX200 8" GPS. With the mirror lock knob and handle on the smaller rear plane of this scope, there is no surface room available for traditional SCT mounting. This bracket raises the motor assembly up and over the handle, allowing the sprocket and belt to install on the top area of the focus knob.

  7. RoboFocus - Remote Power Module

    $150.00
    SKU: RFRP

    Ships in 3-5 Days

    The Remote Power Module is a convenient way for the user to control remotely up to four 120vAC (or 240vAC or 12vDC), outlets through the RoboFocus control program on the PC. Outlets can be connected to observatory accessories such as CCD cameras, heaters, dew zappers, video cameras, etc. Each outlet has its own pilot light. Removing source power to the module will reset all outlets to "OFF", while disconnecting from the control program software leaves each in its current state.

  8. RoboFocus - RF3 Controller

    $330.00
    SKU: ROB-RFC

    Ships in 3-5 Days

    The RoboFocus control module can be purchased separately as a backup unit or to combine with an additional motor kit that was previously obtained.

    FREE SHIPPING(48 States)
  9. RoboFocus - RF3 International

    $495.00
    SKU: ROB-RF3I

    Ships in 3-5 Days

    Complete RoboFocus system, ready to install and operate on your specific telescope/focuser. System includes custom designed stepper motor, RF3 control module, mounting hardware (brackets, shaft coupler, and/or timing sprocket), 2
    FREE SHIPPING(48 States)
  10. RoboFocus - RF3 Upgrade

    $35.00
    SKU: RFU

    Ships in 3-5 Days

    Owners of earlier Model 1 and Model 2 RoboFocus control units can have these devices upgraded to version 3.1 at a fixed cost. This upgrade includes the replacement of 3 IC chips, new firmware and two circuit board upgrades
  11. RoboFocus - RF3 Van Slyke

    $335.00
    SKU: ROB-RF3V

    Ships in 3-5 Days

    Van Slyke Engineering, (and other focuser manufacturers), obtains the RF3 motor directly from Technical Innovations and build into focuser as requested
    FREE SHIPPING(48 States)
  12. RoboFocus - RoboFocus

    $495.00
    SKU: ROB-RF3

    Ships in 3-5 Days

    Complete RoboFocus system, ready to install and operate on your specific telescope/focuser. System includes custom designed stepper motor, RF3 control module, mounting hardware (brackets, shaft coupler, and/or timing sprocket), power converter/adapter (110vAC to 12vDC), cables, PC software (on CD) and comprehensive instruction manual.

    FREE SHIPPING(48 States)
  13. RoboFocus - TAK Bracket for FSQ106

    $35.00
    SKU: ROB-RFB2

    Ships in 3-5 Days

    Custom bracket for Takahashi rack-and-pinion focusers. This bracket is designed for both the 2 and 4 inch focusers. It is made with 0.125 aluminum with an attractive black power coat finish. The bracket is very stable and designed for fast and easy RoboFocus motor mounting.

  14. RoboFocus - TAK Bracket for FSQ106ED and Epsilon 180ED

    $35.00
    SKU: ROB-RFB3

    Ships in 3-5 Days

    Custom bracket for Takahashi "new Q" and ED180 rack-and-pinion focusers. This bracket is designed for both the 2 and 4 inch focusers. It is made with 0.125 aluminum with an attractive black power coat finish.

  15. RoboFocus - USB to Serial Adapter

    $23.00
    SKU: ROB-RFUSB

    Ships in 3-5 Days

    Small single USB to serial adapter allows connection of RoboFocus control module to a PC USB port. Recognized as "plug-n-play" by Windows XP, adapter is auto-configured and assign COM port designation.

15 Item(s)
Set Descending Direction

Technical Innovations was started in 1991 to provide amateur astronomers and schools an affordable, permanent observatory to maximize their ability to view and record objects and events in our universe. Since that starting date, we have placed into service more than 1,200 high quality, reasonably priced fiberglass domes. In keeping with the evolving technology, Technical Innovations also developed and now markets, a line of observatory automation equipment.

Technical Innovations is the registered dba (doing business as) of NetLink Technologies, Inc. The company is owned by Jerry and Cecile Smith of Chevy Chase, Maryland. Technical Innovations was acquired in February of 2002 from the founders, John and Meg Menke. The Menkes are serious amateur astronomers and remain active in several groups. We are thankful to John and Meg for the years of hard work and innovation behind the successful market position Technical Innovations finds itself today. Cecile and Jerry are  dedicated to the future strength and success of the company, through strong business practices and continued product development and improvement.