Happily Serving You in the Same Location for Over 58 Years!

Welcome!

Focuser Upgrade Kits

8 Item(s)

per page

Set Descending Direction
  1. RoboFocus - TAK Bracket for FSQ106ED and Epsilon 180ED

    RoboFocus - TAK Bracket for FSQ106ED and Epsilon 180ED

    Custom bracket for Takahashi "new Q" and ED180 rack-and-pinion focusers. This bracket is designed for both the 2 and 4 inch focusers. It is made with 0.125 aluminum with an attractive black power coat finish. The bracket is very stable and designed for fast and easy RoboFocus motor mounting.

    ...
    Learn More
    Model#: RFB3
    $35.00

  2. RoboFocus - AP Bracket

    RoboFocus - AP Bracket

    Custom bracket for Astro Physics focusers. This bracket is designed for both the 2 and 4 inch focusers. It is made with 0.125 aluminum with an attractive black power coat finish. The bracket is very stable and designed for fast and easy RoboFocus motor mounting.

    ...
    Learn More
    Model#: RFB1
    $35.00

  3. RoboFocus - Hand Paddle

    RoboFocus - Hand Paddle

    The RF3 Hand Paddle allows manual focusing via a small hand controller on a 12 foot cable. The "in/out" buttons move the stepper motor to achieve visual focus. These buttons are duplicates of the ones on the RoboFocus controller box.

    ...
    Learn More
    Model#: RFHP
    $30.00

  4. RoboFocus - RF3 Controller

    RoboFocus - RF3 Controller

    The RoboFocus control module can be purchased separately as a backup unit or to combine with an additional motor kit that was previously obtained.

    ...
    Learn More
    FREE SHIPPING
    (48 States)
    Model#: RFC
    $330.00

  5. RoboFocus - JMI DX1/DX2 Bracket

    RoboFocus - JMI DX1/DX2 Bracket

    Custom bracket for JMI DX1 and DX2 focusers. Bracket is made with 0.125 aluminum with an attractive black powder coat finish. The bracket is very stable and designed for fast and easy RoboFocus motor mounting.

    Note: Two holes must be drilled in the focuser housing base. TI will drill and mount bracket at no charge if desired.

    ...
    Learn More
    Model#: RFB4
    $35.00

  6. RoboFocus - TAK Bracket for FSQ106

    RoboFocus - TAK Bracket for FSQ106

    Custom bracket for Takahashi rack-and-pinion focusers. This bracket is designed for both the 2 and 4 inch focusers. It is made with 0.125 aluminum with an attractive black power coat finish. The bracket is very stable and designed for fast and easy RoboFocus motor mounting.

    ...
    Learn More
    Model#: RFB2
    $35.00

  7. RoboFocus - RF3 Upgrade

    RoboFocus - RF3 Upgrade

    Owners of earlier Model 1 and Model 2 RoboFocus control units can have these devices upgraded to version 3.1 at a fixed cost. This upgrade includes the replacement of 3 IC chips, new firmware and two circuit board upgrades ... Learn More
    Model#: RFU
    $35.00

  8. RoboFocus - LX200 8 GPS Bracket

    RoboFocus - LX200 8 GPS Bracket

    Custom bracket for the LX200 8" GPS. With the mirror lock knob and handle on the smaller rear plane of this scope, there is no surface room available for traditional SCT mounting. This bracket raises the motor assembly up and over the handle, allowing the sprocket and belt to install on the top area of the focus knob.

    ...
    Learn More
    Model#: RFB5
    $35.00

8 Item(s)

per page

Set Descending Direction