JavaScript seem to be disabled in your browser.

You must have JavaScript enabled in your browser to utilize the functionality of this website.

Focuser Upgrade Kits

- The product Astrodon - 1.25 " Mounted B Filter has been added to comparison list.
- The product JMI Case for CPC-800 has been added to comparison list.
- The product JMI - Carrying Case for Meade LX 10 " has been added to comparison list.
- The product JMI - Carrying Case for Meade LX 10 " has been added to comparison list.
- The product JMI - Extra-Large-Format Cassegrain Base has been added to comparison list.
- The product JMI - Extra-Large-Format Cassegrain Base has been added to comparison list.

JMI - Cassegrain Base for EV Focusers

Base for EV Focuser with 2 inch Cassegrain Thread ... Learn More
Model#: EV-BASC

$44.00
- | Add to Compare
JMI - EV-VMC Event Horizon Focuser Upgrade - Vixen Cassegrain

Vixen VMC 200, VMC 260The EV-VCM Upgrade makes the following changes to an EV-1c, EV-2c or EV-3c focuser to prepare it to replace the stock focuser on the Vixen Cassegrain:1) Upgrade to a special Vixen Cassegrain Base ... Learn More
Model#: EVUPGVMC

$80.00
- | Add to Compare
JMI - Extra-Large-Format Cassegrain Base

Base for EV Focuser with 4 inch Cassegrain Thread ... Learn More
Model#: EV-BASX

$84.00
- | Add to Compare
JMI - Focuser Backup Plate - Curved

For adding support when mounting JMI EV, NGF (1.25" and 2") or RCF focusers on Sonotube (cardboard) or wooden optical tubes. (Will not work with the EV-75 Upgrade.) The plates can be easily curved or flattened as needed ... Learn More
Model#: ADPTBUPC

$17.00
- | Add to Compare
JMI - Focuser Backup Plate - Flat

For adding support when mounting JMI EV, NGF (1.25" and 2") or RCF focusers on Sonotube (cardboard) or wooden optical tubes. (Will not work with the EV-75 Upgrade.) The plates can be easily curved or flattened as needed ... Learn More
Model#: ADPTBUPF

$17.00
- | Add to Compare
PetersonEng - EZ Focus Kit

his kit is intended for use with all Meade 7" through 12" Schmidt-Cassegrain and Maksutov-Cassegrain telescopes - including the LX200GPS, the LX200 Classic, the LX90, the LX50 and the LX10 ... Learn More
Model#: EZFocusKit

$29.99
- | Add to Compare
RoboFocus - AP Bracket

Custom bracket for Astro Physics focusers. This bracket is designed for both the 2 and 4 inch focusers. It is made with 0.125 aluminum with an attractive black power coat finish ... Learn More
Model#: RFB1

$30.00
- | Add to Compare
RoboFocus - Hand Paddle

The RF3 Hand Paddle allows manual focusing via a small hand controller on a 12 foot cable. The "in/out" buttons move the stepper motor to achieve visual focus. These buttons are duplicates of the ones on the RoboFocus controller box ... Learn More
Model#: RFHP

$35.00
- | Add to Compare
RoboFocus - JMI DX1/DX2 Bracket

Custom bracket for JMI DX1 and DX2 focusers. Bracket is made with 0.125 aluminum with an attractive black powder coat finish. The bracket is very stable and designed for fast and easy RoboFocus motor mounting ... Learn More
Model#: RFB4

$35.00
- | Add to Compare
RoboFocus - LX200 8 GPS Bracket

Custom bracket for the LX200 8" GPS. With the mirror lock knob and handle on the smaller rear plane of this scope, there is no surface room available for traditional SCT mounting ... Learn More
Model#: RFB5

$35.00
- | Add to Compare
RoboFocus - RF3 Controller

The RoboFocus control module can be purchased separately as a backup unit or to combine with an additional motor kit that was previously obtained ... Learn More

FREE SHIPPING
(excludes AK & HI)
Model#: RFC

$335.00
- | Add to Compare
RoboFocus - RF3 Upgrade

Owners of earlier Model 1 and Model 2 RoboFocus control units can have these devices upgraded to version 3.1 at a fixed cost. This upgrade includes the replacement of 3 IC chips, new firmware and two circuit board upgrades ... Learn More
Model#: RFU

$35.00
- | Add to Compare
RoboFocus - TAK Bracket for FSQ106

Custom bracket for Takahashi rack-and-pinion focusers. This bracket is designed for both the 2 and 4 inch focusers. It is made with 0.125 aluminum with an attractive black power coat finish ... Learn More
Model#: RFB2

$35.00
- | Add to Compare
RoboFocus - TAK Bracket for FSQ106ED and Epsilon 180ED

Custom bracket for Takahashi "new Q" and ED180 rack-and-pinion focusers. This bracket is designed for both the 2 and 4 inch focusers. It is made with 0.125 aluminum with an attractive black power coat finish ... Learn More
Model#: RFB3

$35.00
- | Add to Compare
Starlight Instruments - Base for 2.0 " Dia Focuser, Curved with Leveling Screws - Custom Machined Radius

Base for 2 ... Learn More
Model#: BA20CL

$79.00
- | Add to Compare
Starlight Instruments - Base for 2.0 " Dia Focuser, Curved, Custom Machined Radius

Base for 2 ... Learn More
Model#: BA20C

$69.00
- | Add to Compare
Starlight Instruments - Base for 2.0 " Dia Focuser, Flat

Base for 2 ... Learn More
Model#: BA20F

$29.00
- | Add to Compare
Starlight Instruments - Base for 2.0 " Dia Focuser, Flat with Leveling Screws

Base for 2 ... Learn More
Model#: BA20FL

$39.00
- | Add to Compare
Starlight Instruments - Base for 3.0 " Dia Focuser, Flat with Leveling Screws

SpecificationsBase for 3 ... Learn More
Model#: BA30FL

$49.00
- | Add to Compare
Starlight Instruments - Micro Touch Focusing System - 2 Piece Kit for Control of 2.0 ", MPA Retrofits, and Micro Feather TouchÂ® Focusers - WIRED

Micro Touch Focusing System Kit for Control of 2.0", MPA Retrofits, and Micro Feather Touch® Telescope Focusers. The MicroTouch allows autofocusing of a CCD camera when interfaced with a computer (via USB) ... Learn More

FREE SHIPPING
(excludes AK & HI)
Model#: MKIT20

$549.00
- | Add to Compare

All transactions must be approved by
Woodland Hills Telescopes before shipping

Will only honor current page prices!
International Orders

International Orders

Site designed and hosted by: GammaFX, Inc. Web Design Studio

© 2011 Woodland Hills Telescopes, All Rights Reserved.

Follow us on: